Setting up a DMA card is not complicated, but it has to be done in the right order. Most DMA setup problems come from one skipped step: the wrong firmware for the game, a card not fully seated, the speed-test firmware left on, or the input device not selected in the cheat. Follow the steps below and your DMA setup will work the first time.
This guide walks through a full DMA setup, from choosing the firmware to your first match, and covers troubleshooting. It only describes what our DMA hardware and cheat support.
DMA Setup on LunarCheats
A LunarCheats DMA setup uses a 75T or 100T DMA card, a firmware matched to your game (Basic, Shield or Hook), a second PC, an optional DMA fuser for overlay ESP and an optional Makcu for aimbot. The cheat itself is our Universal DMA cheat, which covers 30+ games with one key.
DMA Setup at a Glance
- Choose the firmware for your game's anti-cheat.
- Install the DMA card in your gaming PC.
- Connect the card to your second PC.
- Run the speed test.
- Activate your gaming firmware.
- Connect the fuser.
- Connect the Makcu.
- Launch the DMA cheat and run the move test.
Before You Start Your DMA Setup
Make sure you have everything on hand:
- A DMA card, or a DMA starter kit with all cables
- The right firmware for your game
- A second PC, or the mini PC option from our kits
- Optional: a fuser and a Makcu
- A free PCIe slot on your gaming PC's motherboard
Step 1: Choose the DMA Firmware for Your Anti-Cheat
The firmware decides whether your DMA setup works on a given game. Match it to the strictest anti-cheat you play against:
- BattlEye, Ricochet, low-tier EAC (Warzone, Black Ops 7, Tarkov, DayZ): Basic
- Every EAC tier and EA Javelin (Fortnite, Rust, Apex Legends, Battlefield): Shield
- Riot Vanguard and ACE (Valorant, Delta Force): Hook
The speed-test firmware shipped with our kits is only for checking your hardware. It is not a gaming firmware.
Step 2: Install the DMA Card
Turn off your gaming PC and unplug it. Open the case, insert the DMA card into a free PCIe slot, press until it is fully seated and secure it with the bracket screw. Close the case. Our firmware supports all motherboards and all processors.
Step 3: Connect the DMA Card to Your Second PC
Connect the DMA card to your second PC with the USB cable. All required cables are included in our DMA kits.
Step 4: Run the Speed Test
Before activating the gaming firmware, use the speed-test firmware to confirm that the card, cable and second PC communicate correctly. If the test fails, check the cable and the card's seating before going further.
Step 5: Activate Your Gaming Firmware
On the second PC, run our firmware activator. It works with any Windows 10 or 11 version, including 24H2 and 25H2. On the gaming PC, Windows 11 is recommended. Hook requires no BIOS modifications, and our support team guides you through the settings for other tiers.
Step 6: Connect the DMA Fuser
Plug your gaming PC's video output and your second PC's video output into the fuser, then connect the fuser to your monitor. Our DMA Fuser is plug and play, with no EDID flash needed. Set both PCs to your monitor's native resolution and refresh rate. For 1440p 240 Hz or 4K 120 Hz, use the 4K Fuser.
Step 7: Connect the Makcu for DMA Aimbot
Plug your mouse into the Makcu, connect the Makcu to your gaming PC and link it to your second PC. The gaming PC sees it as a regular mouse.
Step 8: Launch the DMA Cheat
Start the Universal DMA cheat on the second PC. Select your input device (Makcu, KmBox and others are supported), connect, and run the move test. Then configure ESP and aimbot, save your config and launch the game.
DMA Setup Troubleshooting
No Connection Between Card and Second PC
Check the USB cable, try another USB port on the second PC and make sure the card is fully seated in the PCIe slot.
Speed Test Fails
Reseat the card, check the cable and confirm the second PC recognizes the device.
Fuser Shows Only One PC
Check both video inputs, confirm both PCs output the same resolution and refresh rate, and check the monitor input.
Aim Doesn't Move
Re-run the move test, confirm the correct input device and mode are selected, and check the Makcu connections.
Game Detects Something Wrong
Confirm your firmware tier matches the game's anti-cheat. Basic doesn't cover Fortnite, Rust, Apex, Valorant or Delta Force.
DMA Setup Mistakes to Avoid
- Playing on the speed-test firmware.
- Choosing firmware after buying the card for the wrong game.
- Leaving the card half-seated.
- Mismatched refresh rates between the two PCs and the fuser.
- Aggressive aim settings. A clean setup doesn't hide obvious play.
DMA Setup Summary
A DMA setup comes down to eight steps: pick the firmware for your anti-cheat, install and connect the card, run the speed test, activate the firmware, connect the fuser and Makcu, then launch the DMA cheat and run the move test. Our 24/7 support can help at any step. New to DMA? Start with the DMA starter kit guide and our DMA cards and firmware guide.
DMA Setup FAQ
How long does a DMA setup take?
Once the hardware is in hand, most users complete the steps in one session, with support available if needed.
Do I need to change BIOS settings for my DMA setup?
Not with Hook, which needs no BIOS modifications. For Basic and Shield, our support team guides you through any settings needed.
Can I play on the speed-test firmware?
No. It only checks that the hardware works. Activate Basic, Shield or Hook to play.
Which Windows versions does DMA setup support?
The firmware activator on the second PC supports any Windows 10 or 11 version, including 24H2 and 25H2. Windows 11 is recommended on the gaming PC.
Do I need a fuser for my DMA setup?
Only if you want ESP on your gaming monitor. Otherwise, the ESP shows on the second PC's screen.
More DMA Guides
Ready to play? Get the Universal DMA cheat. More guides on the topic: Makcu vs KmBox: Best Input Box for DMA Aimbot, Best DMA Fuser for 1440p 240Hz and 4K (2026) and DMA Fuser Explained: Do You Need One?.
